Spotlight
Faculty Profiles
Labs
New Laboratories
IITR-Penn State Research Initiative
Ongoing Projects
Completed Projects
Student Section
Research Scholars Day 16th May, 2018
About Us
Tribology Laboratory

 

 

 

 

 

 

 

 

 

 

 

 

Tribology is the science and technology of interacting surfaces in relative motion. This includes study of friction, lubrication, contact mechanics, surface damage processes and surface optimization. It is highly multidisciplinary and spans many applications including physics, chemistry, materials science, biology and engineering. A particular area of current concern is the reduction of friction in order to increase the efficiency of machines and thereby reduce global energy use. In the field of Tribology (friction, lubrication and wear), research focuses on experimentally verified computational and numerical simulation for the prediction of the static and dynamic response of tribo-contacts (fluid film bearings), lubricant and rheology, hydrodynamic/elasto-hydrodynamic/boundary lubrications, hydrodynamic/hybrid/hydrostatic fluid film bearings

Hydrodynamic Journal Bearing Test Rig.:

In this machine, a power motor is attached, via a flexible coupling, to a horizontally mounted shaft. This shaft is in turn supported by means of two spherical bearings mounted on either side of a support frame. The provision of a frequency converter allows the shaft rotational speed to be varied. The journal bearing itself is installed in a spherical steel unit which is in turn mounted within a steel “housing”. The lubricating oil is supplied by means of a small pump unit from a tank with inlet and outlet on the underside of the steel housing. The temperature of the circulating oil is controlled using a water-cooled heat exchanger. Load is applied to the bearing by means of an hydraulic cylinder. This is attached to the steel housing by a “yoke”. A hand pump is employed to adjust the pressure within the cylinder while a load cell is used to accurately monitor the value of the applied load. A number of K-type thermistors are installed in the bearing and at the oil and cooling water inlets and outlets to monitor temperature. Oil film thickness within the bearing is recorded by means of a series of four evenly distributed inductive sensors

Tribometer:

A tribometer is an instrument that measures tribological quantities, such as coefficient of friction, friction force, and wear volume, between two surfaces in contact. A tribotester is the general name given to a machine or device used to perform tests and simulations of wear, friction and lubrication which are the subject of the study of tribology. Often tribotesters are extremely specific in their function and are fabricated by manufacturers who desire to test and analyze the long-term performance of their products. An example is that of orthopedic implant manufactures who have spent considerable sums of money to develop tribotesters that accurately reproduce the motions and forces that occur in human hip joints so that they can perform accelerated wear tests of their products.

Amsler Wear Testing Machine

 To determine the dynamic coefficient of friction, a laboratory test should simulate the rolling operations as closely as possible and should, therefore , be carried out under conditions of sliding and rolling friction. The Amsler Wear Testing Machine has been found to be suitable for this purpose. Under conditions of relatively light loads and low speeds, it gives the value of the coefficient of friction that exists between the peripheries of two test discs as they roll and slide on each other. The two discs have rounded edges with radius of curvature equal to the maximum radius of the discs. They are made of 4140 steel hardened to a value of 59 Rockwell C, with a finish of 4 to 10 microinches, and are held in contact by means of a spring and screw arrangement. By this means, one disc exerts a force on the other to provide an average pressure at the zone of contact.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Coriolis Mass Flow Meter

The basic operation of Coriolis flow meters is based on the principles of motion mechanics. As fluid moves through a vibrating tube it is forced to accelerate as it moves toward the point of peak-amplitude vibration. Conversely, decelerating fluid moves away from the point of peak amplitude as it exits the tube. The result is a twisting reaction of the flow tube during flowing conditions as it traverses each vibration cycle.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LIST OF PUBLICATIONS:

International  Peer Reviewed Journals:

  1. Vivek Kumar, Satish C. Sharma,  “FEM analysis of hydrostatic thrust pad bearings operating with electrically conducting lubricant”,  Part J: Journal of Engineering Tribology, 2018. (In Press)
  2. Krishkant Sahu, Satish C. Sharma,  “A study on performance of slot-entry hybrid journal bearing considering of effect of surface irregularities”,  Industrial Lubrication and Tribology, 2018. (In Press)
  1. Arvind K. Rajput, Saurabh K. Yadav and Satish C. Sharma. “Effect of geometrical irregularities on the performance of a misaligned hybrid journal bearing compensated with membrane restrictor" Tribology International 115: 619-627, 2017.
  2. Chandra B. khatri and Satish C. Sharma, “Performance of two-lobe non-recessed hybrid journal bearing system under consideration combined influence of textured surface and couple stress lubricant”, Mechanics and Industry, 8.6: 603-623, 2017.

5.         Saurabh K. Yadav, Arvind K. Rajput, Nathi Ram and Satish C. Sharma, “A direct numerical approach to compute the nonlinear rotordynamic coefficient of the non-circular gas journal Bearing”, Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, DOI: 1350650117719602, 2017.  

6.         Saurabh K. Yadav, Arvind K. Rajput, Nathi Ram and Satish C. Sharma, "A novel technique to compute static and dynamic performance characteristics of aerostatic thrust bearing" Industrial Lubrication and Tribology just-accepted (2017): 00-00.

  1. Satish C.Sharma and Prashant B.Kushare, “Nonlinear Transient Response of Rough Symmetric Two Lobe Hole Entry Hybrid Journal Bearing System” Journal of Vibration and Control, 23 (2): pp. 190-219 ,2017.
  2. Chandra B. Khatri and Satish C. Sharma, “Influence of couple stress lubricant on the performance of textured two-lobe slot-entry hybrid journal bearing system”, Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, 231(3). pp. 366-384, 2017.  
  3. Vivek Kumar, Satish C.Sharma,  “ Combined Influence of Couple Stress Lubricant, Recess Geometry and method of compensation on the performance of Hydrostatic circular Thrust pad Bearing”, Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, 231 (6): pp. 716-733, 2017.  
  4. Dharmendra jain and Satish C.Sharma,  "Dynamic analysis of a 2-lobe geometrically imperfect journal bearing system." Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology231.7: 934-950, 2017.
  5. Dharmendra jain and Satish C.Sharma, “Combined influence of couple Stress lubricant and geometric inperfection of journal on the performance of Membrane Compansated Two-lobe Hybrid Journal Bearing”, International Journal of Surface Science and Engineering, 11.3 : pp. 191-224, 2017.
  6. Chandra B. khatri and Satish C. Sharma, “Behaviour of two-lobe hole-entry hybrid journal bearing system under the combined influence of textured surface and micropolar lubricant”, Industrial Lubrication and Tribology, 69.6: 844-862, 2017.
  7. Vivek Kumar, Satish C.Sharma,  “ Performance of Annular Recessed Hydrostatic Tilted Thrustpad Bearing Operating with Couple Stress Lubricant”, International Journal of Surface Science and Engineering, 11.4: 344-369, 2017.
  8. Vivek Kumar, Satish C.Sharma,  “Dynamic characteristics of compensated hydrostatic thrust pad bearing subjected to external transverse magnetic field”, Acta Mechanica, DOI 10.1007/s00707-017-1976-3: 1-24,  2017.
  9. Satish C. Sharma and Chandra B. Khatri, “Electro-rheological fluid lubricated textured multi-lobe hole-entry hybrid journal bearing system”, Journal of Intelligent Material Systems and Structures, 2017. DOI: 1045389X17742731.

 

  1. Thakre, G. D., Sharma, S. C., Harsha, S. P., & Tyagi, M. R.  “A theoretical study of ionic liquid lubricated μ-EHL line contacts considering surface texture”, Tribology International, 94, 39-51, 2016.
  2. Sharma, Satish C., and Saurabh K. Yadav. "A comparative study of full and partial textured hybrid orifice compensated circular thrust pad bearing system." Tribology International 95 : 170-180, 2016.
  3. Khatri, Chandra B., and Satish C. Sharma. "Influence of textured surface on the performance of non-recessed hybrid journal bearing operating with non-Newtonian lubricant." Tribology International 95: 221-235, 2016.
  4. Arvind K Rajput and Satish C Sharma, “Combined influence of geometric imperfections and misalignment of journal on the performance of four pocket hybrid journal bearing.” Tribology International 97:59-70, 2016.
  5. Saurabh Kumar Yadav and Satish C. Sharma, “Performance of hydrostatic textured thrust bearing with supply holes operating with non-Newtonian lubricant." Tribology Transactions 59.3 : 408-420, 2016.
  6. Harak, S.S., Sharma, S.C., Harsha, S.P., Dynamic Analysis of Draft Gear and Draft Pad of Freight Wagon Due To Localized Defects using FEM, International Journal of Acoustics and Vibration, 21.3: 281-291, 2016.
  7. Yadav, Saurabh K., and Satish C. Sharma. "Finite element analysis of tilted thrust pad bearings of various recesses shapes considering thrust pad flexibility." Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, 230.7: 872-893, 2016.
  8. Chandra B. Khatri and Satish C. Sharma, “Performance of 180º partial hole-entry hybrid journal bearing considering the combined influence of surface roughness and non-Newtonian behaviour of lubricant”, International Journal of Surface Science and Engineering, 10.6 : 527-558, 2016.

 

  1. Satish C Sharma and Prashant B. Kushare, “Two lobe non-recessed roughened hybrid journal bearing-A comparative study”, Tribology International, 83:pp.51-58, 2015.
  2. Dharmendra jain and Satish C.Sharma, “Two-lobe geometrically imperfect hybrid journal bearing operating with power law lubricant”, Proceedings IMechE, Part J: Journal of Engineering Tribology, 229.1, pp. 30-46, 2015.
  3. Thakre, Gananath D., Satish C. Sharma, S. P. Harsha, and M. R. Tyagi. "A parametric investigation on the microelastohydrodynamic lubrication of power law fluid lubricated line contact." Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, 229.10: 1187-1205, 2015.
  4. Dharmendra jain and Satish C.Sharma, “ Combined influence of geometric irregularities of journal and turbulence on the performance of four-lobe hybrid journal bearing." Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology 229.12: 1409-1424, 2015.
  5. Kanoje, Nagvendra Kumar, Satish C. Sharma, and Suraj P. Harsha. "Subsurface crack propagation with different inclusion under a wheel–flat LEFM analysis using dynamics conditions." International Journal of Vehicle Noise and Vibration 11.1,pp : 1-17, 2015.
  6. Prashant B. Kushare and Satish C.Sharma, "Influence of wear on the performance of 2-lobe slot entry hybrid journal bearings" Mechanics & Industry, 16.5: 502, 2015.
  7. Kushare, Prashant B., and Satish C. Sharma, "A study of 2-lobe symmetric hole entry hybrid journal bearing operating with non-Newtonian lubricant considering thermal effects." Tribology International 92: 567-576, 2015. 

 

  1. Saurabh Kumar Yadav and Satish C Sharma, “Performance of hydrostatic tilted thrust pad bearings of various recess shapes operating with Non-Newtonian lubricant”, Finite Elements in Analysis and Design 87, pp. 43-55, 2014.
  2. Arvind K. Rajput, and Satish C Sharma, “Stability of a Constant Flow Valve Compensated Multirecess Conical Hybrid Journal Bearing Operating with Micropolar Lubrican”, Lubrication Science 26.5, pp. 347-362, 2014.
  3. Satish C Sharma and Saurabh Kumar Yadav, “Performance analysis of a fully textured hybrid circular thrust pad bearing system operating with non-Newtonian lubricant”Tribology International, 77: pp. 50-64,2014.
  4. Gananath D. Thakre, Satish C. Sharma, S.P. Harsha and M.R. Tyagi, “Tribological failure analysis of gear contacts of Exciter Sieve gear boxes” Engineering Failure Analysis, 36: pp.75-91, 2014.
  5. Arvind K Rajput and Satish C Sharma, “A study of capillary-compensated geometrically imperfect six-pocket hybrid journal bearing of various geometric shapes of recess” Proceedings IMechE, Part J: Journal of Engineering Tribology; 228(2): pp. 170-186, 2014.
  6. Prashant B.Kushare and Satish C.Sharma, “Nonlinear Transient Stability Study of Two Lobe Symmetric Hole Entry Worn Hybrid Journal Bearing Operating With Non-Newtonian Lubricant” Tribology International, 69: pp. 84-101, 2014.
  7. Nathi Ram and Satish C. Sharma, "Influence of Wear on the Performance of Hole-Entry Hybrid Misaligned Journal Bearing in Turbulent Regime", Industrial Lubrication and Tribology, Vol. 66 (4), 2014.
  8. Prashant B.Kushare and Satish C.Sharma, “Surface roughness effect on the Performance of 3-lobe symmetric hole entry hybrid journal bearings”, Applied Mechanics and Materials Vol. 592, pp. 1190-1194, 2014.
  9. Yadav, Saurabh Kumar, and Satish C. Sharma. "Performance comparison of partial and full textured thrust bearing operating with non-Newtonian lubricant." Applied Mechanics and Materials. Vol. 592, pp. 1376-1380, 2014.
  10. Nagvendra kumar kanoje, Sharma, Satish C., and S. P. Harsha. "EPFM Analysis of Subsurface Crack Beneath a Wheel Flat Using Dynamic Condition." Procedia Materials Science 6, pp: 43-60, 2014.
  11. Kanoje, Nagvendra Kumar, Satish C. Sharma, and S. P. Harsha. "Wheel-rail and wheel-flat as a coupled system: Contact dynamics modeling with finite element analysis." Journal of Coupled Systems and Multiscale Dynamics 2.1, pp: 20-27, 2014.
  12. Harak, S. S., S. C. Sharma, and S. P. Harsha. "Structural dynamic analysis of freight railway wagon using finite element method." Procedia Materials Science6, pp: 1891-1898, 2014.

 

  1. Prashant B Kushare and Satish C Sharma, “A study of two lobe non recessed worn journal bearing operating with non-Newtonian lubricant”, Proceedings IMechE, Part J: Journal of Engineering Tribology;227(12): pp. 1418-37, 2013.
  2. Satish C. Sharma, Saurabh K. Yadav, “Performance of hydrostatic circular thrust pad bearing operating with Rabinowitsch fluid model”, Proceedings IMechE, Part J: Journal of Engineering Tribology; 227(11): pp. 1272-84, 2013.
  3. Satish C. Sharma, Arvind K. Rajput,” Effect of geometric imperfections of journal on the performance of micropolar lubricated 4-pocket hybrid journal bearing,” Tribology International, Vol . 60, pp. 156–168, 2013.
  4. Nathi Ram, Satish C. Sharma, “A Study of Misaligned Hole-Entry Worn Journal Bearing Operating In Turbulent Regime”, Industrial Lubrication and Tribology. 65(2), 2013, pp.108-118.
  5. P.K. Kankar, Sharma C. Satish and S.P. Harsha, “Fault diagnosis of rolling element bearing using cyclic autocorrelation and wavelet transform”,  Neurocomputing, 110, 2013, pp.9-17.
  6. Arvind K. Rajput, Satish C. Sharma,  “Analysis of externally pressurized multirecess conical hybrid journal bearing system using micropolar lubricant,”  IMechE (J  Engg. Tribology), Vol. 227(9)  2013, pp. 943-961.

 

  1. J. Stahlmann, E. Rajasekhar Nicodemus and Satish C. Sharma,  P. Groche, “Surface roughness evaluation in FEA simulations of bulk metal forming process”, WEAR, 288, pp. 78-87, 2012.
  2. Satish C. Sharma, Vikas M. Phalle, and S. C. Jain, “Performance Analysis of a 2-Lobe Worn Multirecess Hybrid Journal Bearing System Using Different Flow Control Devices,” Tribology International, vol. 52, pp. 101-116, 2012.
  3. Nathi Ram, Satish C. Sharma, “Analysis of Orifice Compensated Non-Recessed  Hole-Entry Hybrid Journal Bearing operating with Micropolar Lubricants”, Tribology International, vol. 52, pp. 132-143, 2012.
  4. Satish C. Sharma, Arvind K. Rajput,  “Influence of Micropolar Lubrication on the Performance of 4-Pocket Capillary Compensated Conical Hybrid Journal Bearing” Advances in Tribology, Volume 2012  Article ID 898252, 2012, pp-1-18.
  5. Arvind K. Rajput, Satish C. Sharma, Marut Shukla And Souvik Roy   “A parametric study of S- tube Coriolis mass flow meter”, Sensors & Transducers, Vol.142, Issue 7, 2012, pp-118-129.
  6. Satish C. Sharma, Vikas M. Phalle, and S. C. Jain, "Combined Influence of Wear and Misalignment of Journal on the Performance Analysis of 3-Lobe Three-Pocket Hybrid Journal Bearing Compensated with Capillary Restrictor," ASME Journal of Tribology, Vol.134, 011703,2012.
  7. E. Rajasekhar Nicodemus and Satish C. Sharma, “Performance Characteristics of Micropolar Lubricated Membrane-Compensated Worn Hybrid Journal Bearings”, Tribology Transactions, Vol. 55, pp. 59 -70, 2012.
  8. K.M. Jagadeesha, T. Nagaraju, Satish C. Sharma, and S. C. Jain, “3D Surface Roughness Effects on Transient Non-Newtonian Response of Dynamically Loaded Journal Bearings”, Tribology Transactions, Vol. 55, pp. 32 -42, 2012.
  9. P.K. Kankar, Sharma C. Satish and S.P. Harsha, “Vibration Based Performance Prediction of Ball Bearings caused by Localized Defects”, Nonlinear Dynamics, 69.3 : 847-875, 2012.
  10. P.K. Kankar, Sharma C. Satish and S.P. Harsha, “Nonlinear Vibration Signature Analysis of a High Speed Rotor Bearing System due to Race Imperfection”, J. of Computational and Nonlinear Dynamics, Vol. 7, No. 1, pp. 011014-29, 2012
  11. Pravin P. Patil, Satish C. Sharma and S.C. Jain, “Response Surface Modeling of Vibrating Omega Tube (Copper) Electromechanical Coriolis Mass Flow Sensor", Expert Systems with Applications, vol.39, pp.4418-4426, 2012.
  12. Pravin P. Patil, Satish C. Sharma and S.C. Jain, “Performance Evaluation of a Copper Omega Type Coriolis Mass Flow Sensor with an Aid of ANFIS Tool", Expert Systems with Applications, vol.39, pp.5019-5024, 2012.
  13. Satish C. Sharma, Vikas M. Phalle, S.C.Jain, “Performance of 2-Lobe Multirecess Constant Flow Valve Compensated Hybrid Journal Bearing by Considering Wear”, Industrial Lubrication and Tribology. 64(3), 2012, pp.171-181.
  14. Unnati A Joshi, Satish C Sharma, S. P. Harsha, “Effect of Carbon Nanotube Orientation on the Mechanical Properties of Nano Composites”, Composites Part B: Engineering, Elsevier Publishers, 43( 4) 2012 pp. 2063-71.
  15. Anand Y Joshi, Satish C Sharma, S.P.Harsha, “Chaotic Response Analysis of Single Walled Carbon Nanotube due to Surface Deviations” NANO, 7(2) 2012, pp.  1250008-1-10.
  16. Unnati A Joshi, Satish C Sharma, S.P. Harsha, Influence of Dispersion and Alignment of Nanotubes on the Strength and Elasticity of Carbon Nanotubes Reinforced Composites, ASME Journal of Nanotechnology in Engineering and Medicine, American Institute of Physics2(4) 2012.
  17. Anand Y Joshi, Satish C Sharma, S. P. Harsha, “Nonlinear Dynamic Analysis of Single walled carbon Nanotube based mass sensors due to surface deviations”, ASME Journal of Nanotechnology in Engineering and Medicine, American Institute of Physics, 2(4), 2012.

 

  1. Satish C. Sharma, Nathi Ram, “Influence of Micropolar Lubricants on the Performance of Slot-Entry Hybrid Journal Bearing”, Tribology International, Vol.44, No.12, pp. 1852-1863, 2011.
  2. R.K. Gautam, S. Ray, Satish C. Sharma, S. C. Jain and R Tyagi, “Dry Sliding Wear behavior of hot forged and anneled Cu-Cr-graphite in-situ Composites,” WEAR, Vol.271, pp. 658-664, 2011.
  3. Satish C. Sharma, and E. Rajasekhar Nicodemus, and Nathi Ram, “A study of misaligned micropolar lubricated membrane compensated hybrid journal bearing,” ASME Journal of Tribology, Vol.133, pp.031703-031709, 2011.
  4. Satish C. Sharma, Vikas M. Phalle, S.C.Jain, “Influence of Wear on The Performance of a Multirecess Conical Hybrid Journal Bearing Compensated With Orifice Restrictor, Tribology International, Vol. 44(12), pp. 1754-1764, 2011.
  5. E. Rajasekhar Nicodemus, Satish C. Sharma, “Orifice Compensated Multirecess Hydrostatic/Hybrid Journal Bearing System of Various Geometric Shapes of Recess Operating with Micropolar Lubricant”, Tribology International, Vol.44,No.3, pp.284-296,2011.
  6. Satish C. Sharma, Vikas M. Phalle, S.C.Jain, “Performance Analysis of a Multirecess Capillary Compensated Conical Hydrostatic Journal Bearing”, Tribology International, Vol.44, No.5, pp.617-626, 2011.
  7. Vikas M. Phalle, Satish C. Sharma, S.C.Jain, “Influence of Wear on the Performance of a 2-lobe Multirecess Hybrid Journal Bearing System Compensated with Membrane Restrictor”, Tribology International, Vol.44,No.4, pp.380-395,2011.
  8. Kankar P.K., Sharma Satish C. and Harsha S.P., “Fault Diagnosis of Ball Bearings Using Machine Learning Methods”, Expert Systems with Applications, Vol. 38, No. 3, , pp. 1876-1886, 2011.
  9. Kankar P.K., Sharma Satish C. and Harsha S.P., “Fault Diagnosis of High Speed Rolling Element Bearings Due to Localized Defects using Response Surface Method”, ASME Journal of Dynamic Systems, Measurement and Control, Vol. 133, No. 2, pp.031007-1 to 031007-14, 2011,
  10. Unnati A Joshi, Satish C Sharma, S.P. Harsha, “Analysis of Elastic Properties of Carbon Nanotube Reinforced Nano Composites with Pinhole Defects”, Computational Materials Science, Vol. 50, Issue 11, 2011, 3245-3256, Elsevier Publishers.
  11. Unnati A Joshi, Satish C Sharma, S. P. Harsha, “Effect of Pinhole Defects on the Elasticity of Carbon Nanotube Based Nanocomposites”, ASME Journal of Nanotechnology in Engineering and Medicine, Vol. 2, Issue 1, 2011, 011003-1-7, American Institute of Physics.
  12. Unnati A Joshi, Satish C Sharma, S. P. Harsha, “Modelling and analysis of mechanical behavior of carbon nanotube reinforced composites”, Proceedings of IMechE, Part N: Journal of Nanoengineering and Nanosystems, Vol. 225, Issue 1, 2011.
  13. R.K. Gautam, S. Ray, Satish C. Sharma, S. C. Jain and R Tyagi, “Dry Sliding Wear behavior of hot forged and anneled Cu-Cr-graphite in-situ Composites,” WEAR, Vol.271, pp. 658-664, 2011.
  14. Anand Y Joshi, Satish C Sharma, S. P. Harsha, “Zeptogram Scale Mass sensing using Single Walled Carbon Nanotube Based Biosensors”, Sensors & Actuators : A. Physical, Vol. 168, Issue 2, pp. 275-280, 2011.
  15. Unnati A Joshi, Satish C Sharma, S.P. Harsha, “Effect of waviness on the Mechanical Properties of Carbon Nanotube based Composites”, Physica E: Low Dimensional systems & Nanostructures, Vol. 43, Issue 8, pp. 1453-1460, 2011.
  16. Kankar P.K., Sharma Satish C. and Harsha S.P., “Rolling Element Bearing Fault Diagnosis Using Wavelet Transform”, Neurocomputing, Vol. 74, Issue 10, pp. 1638-1645, 2011.
  17. Anand Y Joshi, S. P. Harsha, Satish C Sharma, “Effect of chirality and atomic vacancies on dynamics of nano resonator based on SWCNT”, Sensor Review, Vol.31(1), pp.47-57,2011.
  18. Anand Y Joshi, S. P. Harsha, Satish C Sharma, “The Effect of Pinhole Defect on Vibration Characteristics of Single Walled Carbon Nanotube”, Physica E: Low Dimensional systems & Nanostructures, Vol. 43, Issue 5, pp.1040-1045, 2011.
  19. Kankar P.K., Sharma Satish C. and Harsha S.P., “Fault Diagnosis of Ball Bearings Using Continuous Wavelet Transform”, Applied Soft Computing, 11(2), pp .2300-2312, 2011.
  20. Kankar P.K., Sharma Satish C. and Harsha S.P., “Rolling Element Bearing Fault Diagnosis using Autocorrelation and Continuous Wavelet Transform”, Journal of Vibration and Control, 17(14), pp. 2081-2094, 2011.
  1. Satish C. Sharma , Pravin P. Patil , Ashish Vasudev, Satish C. Jain, “Performance Evaluation of an Indigenously Designed Copper (U) tube Coriolis Mass sensors”, Measurement, Vol. 43, No.9, pp1165-1172,2010.
  2. E. Rajasekhar Nicodemus, Satish C. Sharma, “A Study of Worn Hybrid Journal Bearing System with Different Recess Shapes Under Turbulent Regimes”, ASME Journal of Tribology. Vol 132 pp.41704-12, 2010.
  3. S. C. Jain, Satish C. Sharma, J.S. Basavaraja and Prashant Kushare, ‘Study of Two-Lobe Four Recessed Hybrid Journal Bearing’, Industrial Lubrication and Tribology, Vol 62, Issue 6, pp.332 – 340, 2010.
  4. Anand Y Joshi, Aashish Bhatnagar, S. P. Harsha, Satish C Sharma,” Vibration Response Analysis of Doubly Clamped Single Walled Wavy Carbon Nanotube Based Nano Mechanical Sensors” ASME Transactions, Journal of Nanotechnology in Engineering and Medicine, Vol.1(3),pp.031004-1-5,2010.
  5. Anand Y Joshi, S. P. Harsha, Satish C Sharma, “Dynamic Behavior of Chiral Fixed Free Single Walled Carbon Nanotube Based Nano Mechanical Mass Sensors due to Atomic Vacancies” Proceedings of IMECH E, Part N: Journal of Nanoengineering and Nanosystems,Vol. 224(2),pp.45-56,2010.
  6. E. Rajasekhar Nicodemus, Satish C. Sharma, “Influence of Wear on the Performance of Multirecess Hydrostatic Journal Bearing Operating with Micropolar Lubricant”, ASME Journal of Tribology 132, 021703-1 to 021703- 10, 2010.
  7. J. Sharana Basavaraja, Satish C. Sharma, Satish C. Jain “A Study of misaligned electrorheological fluid lubricated hole-entry hybrid journal bearing” Tribology International ,Vol. 43, Issues 5-6, Pages 859-1200, 2010.
  8. J.S. Basavaraja, Satish C. Sharma, and S.C. Jain, ‘The Study of ER Fluid Lubricated Misaligned Hole--Entry Hybrid Journal Bearing’, Tribology International, Vol.43,Issue 5-6, pp 1059-1064,2010.
  9. Anand Y Joshi, Satish C Sharma, S. P. Harsha, “Analysis of Crack Propagation in Fixed Free Single Walled Carbon Nanotube under Tensile Loading Using XFEM”, ASME Transactions, Journal of Nanotechnology in Engineering and Medicine, 1, (4), 2010, 041008-7.
  10. Anand Y Joshi, S. P. Harsha, Satish C Sharma “Dynamic Analysis of a Clamped Wavy Single Walled Carbon Nanotube based Nano Mechanical Sensors”, ASME Transactions, Journal of Nanotechnology in Engineering and Medicine 1, (3), 2010, 031007-1-7
  11. Pravin P Patil, Satish C. Sharma, S.C. Jain, “Prediction Modeling of Coriolis Type Mass Flow Sensor Using Neural Network”, Instruments and Experimental Techniques,Vol.54(3),pp.435-439,2010.
  12. Pravin P. Patil, Satish C. Sharma, S.C. Jain, “Development of (Aluminium) ‘U’ Tube type Vibration Based Electromechanical Mass Flow Sensor", Sensors & Transducers Journal , vol.123, issue 12, pp.60-68, Dec. 2010.
  13. S. C. Jain, Satish C. Sharma, J.S. Basavaraja and Prashant Kushare, ‘Study of Two-Lobe Four Recessed Hybrid Journal Bearing’, Industrial Lubrication and Tribology, Vol 62, Issue 6, pp.332 – 340, 2010.
  14. Anand Y Joshi, S. P. Harsha, Satish C Sharma, “Vibration Signature Analysis of Single Walled Carbon Nanotube Based Nano Mechanical Sensors”, Physica E: Low Dimensional Systems & Nanostructures, 42, (8), pp.2115-2123,2010.
  15. Anand Y Joshi, Aashish Bhatnagar, S. P. Harsha, Satish C Sharma, “An Investigation of Mass Sensitivity of Fixed Free Single Walled Carbon Nanotube (SWCNT) Based Nano Mechanical Sensors”, Current NanoScience, 6(6), pp.598-603,2010.
  16. Unnati A Joshi, Preeti Joshi, S.P. Harsha, Satish C Sharma, “Evaluation of the Mechanical Properties of CNT based Composites Using Hexagonal RVE,” ASME Transactions, Journal of Nanotechnology in Engineering & Medicine, 1(3) 031006-1-7,2010.
  1. Kankar P.K., Harsha S.P., Kumar Pradeep and Sharma Satish C., “Fault Diagnosis of a Rotor Bearing System using Response Surface Method”, European Journal of Mechanics / A Solids, Vol. 28, 2009, pp. 841-857.
  2. Unnati A Joshi, Satish C Sharma, S.P. Harsha, “Effects of Pinhole defects on the elasticity of Carbon Nanotube based Nano-Composites” ASME Transactions, Journal of Nanotechnology in Engineering & Medicine, 2,1, 011003-1-7.
  3. J.S. Basavaraja, Satish C. Sharma, and S.C. Jain, ‘Study of Misaligned Roughened Multi-Lobe Hybrid Journal Bearing’, Industrial Lubrication and Tribology, Vol.61, no.4,pp.220-227,2009.
  1. R.K. Gautam, S. Ray, S.C. Jain and Satish C. Sharma, ‘Tribological Behaviour of (Cu–Cr–SiCp) In–Situ composite', WEAR, Vol. 265, pp. 902 – 912, 2008.
  2. J.S. Basavaraja, Satish C. Sharma, and S.C. Jain, ‘Performance of an Orifice Compensated Two Lobe Hole – Entry Hybrid Journal Bearing’, Advances in Tribology, Vol 2008, Article ID 871952, 10 pages, doi:10.1155/2008/871952, 2008.

 

  1. R.K. Awasthi, Satish C. Sharma, and S.C. Jain, 'Effect of Wear on the Performance of Non-Recessed Orifice Compensated Hybrid Journal Bearing', STLE Tribology Trans, Vol. 50, No. 3, pp. 361 – 373, 2007.
  2. T. Nagaraju, Satish C. Sharma, and S.C. Jain, 'Influence of Surface Roughnenss on Non-Newtonian Thermohydrostatic Performance of a Hole – Entry Hybrid Journal Bearing', ASME Jr. of Tribology, Vol. 129, No. 3, pp. 595 – 602, 2007.
  3. R.K. Awasthi, Satish C. Sharma and S.C. Jain, 'Performance of Worn Non – Recessed Hole – Entry Hybrid Journal Bearings,' Tribology International, Vol. 40, no.5, pp. 717 – 734, 2007.      
  1. R.K. Awasthi, S.C. Jain, and Satish C. Sharma, 'Finite Element Analysis of Orifice Compensated Multiple Hole – Entry Worn Hybrid Journal Bearing', Finite Elements in Analysis and Design, Vol. 42, issues 14 – 15, pp. 1291 – 1303, Oct. 2006.
  2. R.K. Awasthi, S.C. Jain, and Satish C. Sharma, 'A Simulation Study of Running in Wear Effect and its Influence on Average Flow Factors', STLE Tribology Transactions, Vol. 49, No. 3, pp. 427 – 438, 2006.
  3. T. Nagaraju, Satish C. Sharma and S.C. Jain, 'Study of Orifice Compensated Hole – Entry Hybrid Journal Bearing Considering Surface Roughness and Flexibility Effects', Tribology International, Vol. 39, No. 7, pp. 715 -–725, 2006.
  4. Vijay Kumar, Satish C. Sharma and S.C. Jain, 'On the Restrictor Design Parameter of Hybrid Journal Bearing for Optimum Rotordynamic Coefficients', Tribology International, Vol. 39, No.4, pp. 356 – 368, 2006.
  1. T. Nagaraju, Satish C. Sharma, and S.C. Jain, "The Stability Margin of Roughened Hole Entry Hybrid Journal Bearing System", STLE Tribology Transactions, Vol. 48, No.1, pp. 140-146, 2005.
  1. Satish C. Sharma, T Nagaraju, and S.C. Jain, "Performance of an Orifice Compensated Hole – Entry Hybrid Journal Bearing System Considering Surface Roughness and Thermal Effects", STLE Tribology Transactions, Vol. 47, No.4, pp. 557 – 556, 2004.
  2. Vijay Kumar, Satish C. Sharma, and S.C. Jain, " Stability Margin of Hybrid Journal Bearing : Influence of Thermal and Elastic Effects", ASME Journal of Tribology, Vol. 126, No. 3, pp. 630 – 634, 2004.
  3. Narendra Singh, Satish C. Sharma, S.C. Jain and Sanjeev Reddy, "Performance of Membrane Compensated Multirecess Hydrostatic / Hybrid Journal Bearing System Considering Various Recess Shapes", Tribology International, Vol. 37, No. 1, pp. 11 – 24, 2004.
  1. Satish C. Sharma, Vijay Kumar, S.C. Jain and T. Nagaraju, "Study of Hole – Entry Hybrid Journal Bearing System Considering Combined Influence of Thermal and Elastic Effects", Tribology International, Vol. 36, No. 12, pp. 903 – 920, 2003.
  2. Vijay Kumar, Satish C. Sharma, and S.C. Jain, "On the Stability Margin of Hole – Entry Hybrid Journal Bearing Considering Viscosity Temperature Variation", STLE Tribology Transactions, Vol. 46, No. 3, pp. 421 – 427, 2003.
  3. T. Nagaraju, Satish C. Sharma and S. C. Jain, ‘Performance of Externally Pressurized Non-Recessed Roughened Journal Bearing System Operating with Non-Newtonian Lubricant’, STLE Tribology Transactions, Vol.46, no.3, pp.404-413, 2003.
  1. Satish C. Sharma, T. Nagaraju and S. C. Jain, ‘Combined Influence of Journal Misalignment and Surface Roughness on the Performance of Orifice Compensated Non-Recessed Hybrid Journal Bearing’, STLE Tribology Transactions,  Vol.45, no.4,pp 457- 463,2002.
  2. Satish C. Sharma, Vijay Kumar, S. C. Jain, T. Nagaraju and Giriraj Prasad, ‘Thermohydrostatic Analysis of Slot-Entry Hybrid Journal Bearing’, Tribology International,Vol. 35, no.9, pp 561-577, 2002.
  3. T. Nagaraju, Satish C. Sharma and S. C. Jain, ‘ Influence of Surface Roughness Effects on Performance of Non-Recessed Hybrid Journal Bearings’, Tribology International,Vol. 35, no.7, pp 467-487, 2002
  4. Satish C. Sharma, S. C. Jain and D. K. Bharuka, ‘ Influence of Recess Shape on the Performance of a Capillary Compensated Circular Thrust Pad Bearing’, Tribology International, Vol. 35, no.6, pp 347-356, 2002.
  1. Satish C. Sharma, S.C. Jain and N. Madhu Mohan Reddy, ‘A Study of Non-Recessed Hybrid Flexible Journal Bearings with Different Restrictors’, STLE Tribo., Transactions,Vol.44, No.2, pp. 310-317, 2001.
  2. Satish C. Sharma, P.L. Sah, S.C. Jain and R. Sinhasan, ‘Static and Dynamic Performance Characteristics of Orifice Compensated Hydrostatic Flexible Journal Bearings with Non-Newtonian Lubricants’, STLE Tribology Transactions,  Vol.44, No.2, pp. 242-248, 2001.
  3. Satish C. Sharma, M. Bhattacharya, Mohd. Khaliquzzama, Amar Sapra, Lalit K. Khandelwal, Mohd. Saif and Rajiv Harbindu, ‘Development of a Mass Flow Meter Based on Coriolis Effect’, Int., Jr. Mech. Engg. , Edu.,(IJMEE, U.K.), Vol.29, No.2, pp.132-146, 2001.
  1. Satish C. Sharma, S.C. Jain and P.L Sah, ‘Effect of Non-Linear Behaviour of Lubricant and Bearing Flexibility on the Performance of Slot-Entry Journal Bearings’, Tribology International, Vol. 33, no. 7, pp. 507-517, 2000.
  1. Satish C. Sharma, S.C. Jain and N. Madhu Mohan Reddy, ‘Influence of Elastic Effects on the Performance of Slot-Entry Journal Bearings’, Tribology International, Vol.32, no.10, pp. 537-551, 1999.
  2. Satish C. Sharma, Vijay Kumar, S.C. Jain, R. Sinhasan and M. Subramanian, ‘A Study of Slot-Entry Hydrostatic/Hybrid Journal Bearing Using the FEM’, Tribology International, Vol.32, no.4, pp 185-196, 1999.
  1. Satish C. Sharma ,‘On the Application of Strain Gauges for a Structural Member Subjected to Complex Type of Loading’, Int. Jr. of Mechanical Engg. Education, (IJMEE, U.K.), Vol. 26, No.3, pp. 241-246, 1998.
  2. Satish C. Sharma, R. Sinhasan, S.C. Jain, N. Singh and S.K. Singh, ‘Performance of Hydrostatic/Hybrid Journal Bearings with Unconventional Recess Geometries’, STLE Tribology Transactions,  Vol. 41, no.3, pp. 375-381, 1998.
  1. S.C. Jain, Satish C. Sharma and T. Nagaraju, ‘Misaligned Journal Effect in Liquid Hydrostatic Nonrecessed Journal Bearings’, WEAR,Vol. 210, pp. 67-75, 1997.
  1. Satish C. Sharma, S.C. Jain,R. Sinhasan and R. Shalia, ‘Comparative Study of the Performance of  Six pocket and Four pocket Hydrostatic/Hybrid Flexible Journal Bearings’, Tribology International, Vol.28, No. 8,pp. 531-539,1995.
  1. Satish C. Sharma, R. Sinhasan, and S.C. Jain, ‘An Elastohydrostatic Study of Hole-Entry Hybrid Flexible Journal Bearing with Capillary Restrictors’, Tribology International, Vol. 26, No.2, pp. 93-107, 1993.
  1. S.C. Jain, R. Sinhasan and Satish C. Sharma, ‘Analytical Study of Flexible Hybrid Journal Bearing System using Different Flow Control Devices’, Tribology International, Vol. 25, No.6, pp. 387-395, 1992.
  2. Satish C. Sharma, S.C. Jain and R. Sinhasan, ‘Performance Characteristics of Constant Flow Valve Compensated Multiple Hole Entry Hybrid Flexible Journal Bearings’, Periodica Polytechnica, Budapest (Hungary)., Vol. 36, No.1, pp.61-84, 1992.
  3. Satish C. Sharma, R. Sinhasan, and S.C. Jain, ‘Performance Characteristics of Multirecess Hydrostatic/Hybrid Flexible Journal Bearing with Membrane Type Variable Flow Restrictor Compensating Element’, WEAR, Vol. 152, pp.279-300, 1992.
  1. R. Sinhasan, Satish C. Sharma and S.C. Jain, ‘Performance Characteristics of Externally Pressurised Orifice Compensated Flexible Journal Bearing’, STLE Tribology Transactions, Vol. 34, No.3, pp. 465-471, 1991.
  1. Satish C. Sharma, R. Sinhasan and S.C. Jain, ‘Elastohydrostatic Analysis of Orifice Compensated Multiple Hole-Entry Hybrid Journal Bearings’, International Journal of Machine Tools and Manufacture, Vol. 30, No. 1, pp. 111-129, 1990.
 
   
  1. R.Sinhasan, Satish C. Sharma and S.C. Jain, ‘Performance Characteristics of Constant Flow Valve Compensated Multirecess Flexible Hydrostatic Journal Bearing’, WEAR, Vol. 134, pp. 335-356, 1989.
  2. Sinhasan, Satish C. Sharma and S.C. Jain, ‘Performance Characteristics of an Externally Pressurised Capillary Compensated Flexible Journal Bearing’, Tribology International, Vol. 22, No.4, pp. 283-293, 1989.
  3. R. Sinhasan, S.C. Jain and Satish C. Sharma, ‘A Comparative Study of Flexible Thrust pad Hydrostatic Bearings with different Restrictors’, WEAR,  Vol. 121, pp. 53-70, 1988.

 

   
  1. R. Sinhasan, S.C. Jain and Satish C. Sharma, ‘Elastic Considerations in the Hydrostatic Lubrication of Capillary Compensated Thrust Bearings of Different Configurations’, WEAR, Vol. 3, No.1, pp. 41-62, 1986.
  2. R. Sinhasan, S.C. Jain and Satish C. Sharma, ‘Orifice Compensated Flexible Thrust Pad Bearings of Different Configurations’, Tribology International, Vol. 19, No. 5, pp. 244-252, 1986.
  1. R. Sinhasan, S.C. Jain and Satish C. Sharma, ‘Elastohydrostatic Lubrication of Capillary Compensated Thrust Pad Bearings’, WEAR, Vol. 91, pp. 131-147, 1983.

National Journals

  1. Vivek Gupta, V.H. Saran and Satish C. Sharma, “A novel technique to measure the rolling resistance of tyres using force transducer”,  Journal of The Institution of Engineers (India): Series C 96.3 (2015): 325-330.
  2. R.K. Awasthi, Satish C. Sharma, and S.C. Jain, ‘Effect of Running-in Wear on the Performance Characteristics of a Hydrodynamic Journal Bearing System’ Indian Journal of Tribology, Vol.4,no.1,Jan.-June 2009,pp1-13.
  3. J.S. Basavaraja, S.C. Jain , and Satish C. Sharma, ' Constant flow valve compensated Hole-Entry Hybrid Journal Bearing Lubricated with ER Fluid A Simulation Study of Rough Hole-Entry Hybrid Journal Bearing Lubricated with ER Fluid,' Indian Journal of Tribology,Vol.4, no1, Jan.-June 2009,pp.43-51.
  4. Suren Kumar, Akhilesh Dwivedi, Sumit Wadhwa, and Satish C. Sharma, ‘Vision Based Lane Detection for Autonomous Navigation’ IURS Journal of Unmanned Robotic Vehicles and Intelligent System’ Vol. 1, Issue 1, pp. 97 – 100, Sept. 2007.
  5. Vijay Kumar, Satish C. Sharma, S.C. Jain and T. Nagaraju, 'Comparative Performance of Hole-Entry Journal Bearing Operating with Different Restrictors', Journal of Institution of Engineering, IE(I) – Journal MC, Vol. 83, October 2002, pp. 116 – 123.
  6. S.C. Jain, Satish C. Sharma and N. Ramesh Babu, ‘Performance Characteristics of Multirecess Hybrid Flexible Journal Bearing in Turbulent Regime’, Journal of Institution of Engineers (India), Vol. 81, Pt Mc/1, pp. 1-8, May, 2000.
  7. P.L. Sah, Satish C. Sharma, S.C. Jain and R. Sinhasan, ‘A Study of Constant Flow Valve Compensated Multirecess Hydrostatic/Hybrid  Flexible Journal Bearing Operating with Non-Newtonian Lubricants’, Journal of Institution of Engineers, Vol. 81, Pt Mc/2, pp. 84-92, 2000.

 

Abstracts Publication

  1. Satish C. Sharma, Vijay Kumar, S.C, Jain, R. Sinhasan and M. Subramanian, ‘A Study on Characteristics of Slot-Entry Journal Bearing Using the FEM’, Proceedings of World Tribology Congress, Abstracts of Papers, Sept. 8-12, 1997 (London), pp. 426, MEP (U.K.).

 

Papers Published/ Presented In International Conferences 

  1. Satish C. Sharma, Chandra B. Khatri, “Performance of textured two-lobe slot-entry hybrid journal bearing system operating with electro-rheological lubricant”, International Conference on Industrial Tribology (ICIT -2017), Kolkata, India, 2017.
  2. Chandra B. Khatri, Satish C. Sharma, “A study on the performance of 3-lobe hole-entry hybrid journal bearing system under the combined influence of micropolar lubricant and textured surface”, International Conference on Industrial Tribology (ICIT -2017), Kolkata, India, 2017.
  3. Krishnkant Sahu, Satish C. Sharma, “Performance Analysis of Geometrically Imperfect Slot Entry Hybrid Journal Bearing System”, International Conference on Industrial Tribology (ICIT -2017), Kolkata, India, 2017.
  4. Saurabh Kumar Yadav, Nathi Ram, Satish C. Sharma, “Influence of non-Newtonian lubricant behavior on the performance of flexible rotor system supported by fluid film bearing”, International Conference on Industrial Tribology (ICIT -2017), Kolkata, India, 2017.
  5. Vivek Kumar, Satish C. Sharma, “Dynamic characteristics of hydrostatic thrust pad bearing operating with micropolar lubricant”, International Conference on Industrial Tribology (ICIT -2017), Kolkata, India, 2017.
  6. Nathi Ram, Saurabh Kumar Yadav, Satish C. Sharma, “Analysis of Asymmetric Slot-Entry Journal Bearing under Turbulent Regime”, International Conference on Industrial Tribology (ICIT -2017), Kolkata, India, 2017.
  7. Prashant B. Kushare, Satish C. Sharma, “Performance of Non-Newtonian Lubricated Worn 2-Lobe Slot Entry Restrictor Bearing System”, International Conference on Industrial Tribology (ICIT -2017), Kolkata, India, 2017.
  8. Suresh Jadhav , Gananath D. Thakre, Satish C. Sharma, “An Investigation on the Tribo-performance of Brass-on-Steel EHL Point Contacts”, International Conference on Industrial Tribology (ICIT -2017), Kolkata, India, 2017.
  9. Suresh Jadhav , Gananath D. Thakre, Satish C. Sharma, “An Investigation on the Tribo-performance of Brass-on-Steel EHL Point Contacts”, International Conference on Industrial Tribology (ICIT -2017), Kolkata, India, 2017.
  10. Abhishek Kumar, Satish C. Sharma, “Influence of surface waviness on the dynamic performance of circular hole-entry hybrid journal bearing system”, International Conference on Industrial Tribology (ICIT -2017), Kolkata, India, 2017.
  11. Sharma C. Satish , and Dharmendra Jain. "Effect of Geometrically Imperfect Journal and Recess Geometry on the Performance of Two Lobe/Circular 4 Pocket Hybrid Journal Bearing System." 71th STLE Annual Meeting & Exhibition  2016, Las, Vegas (USA), May 15-19 , 2016
  12. Satish C. Sharma, Saurabh K. Yadav,   Influence of tilt on the performance of circular trust pad bearing of various recess shapesSTLE 70th Annual Meeting & Exhibition  2015, Dallas, Texas(USA), May 17-21, 2015.
  13. Saurabh K. Yadav, Satish C. Sharma,   Performance of full textured hybrid thrust bearing by considering the temperature variation in oil filmSTLE 70th Annual Meeting & Exhibition  2015, Dallas, Texas(USA), May 17-21, 2015.
  14. Prashant B.Kushare and Satish C.Sharma, “Surface roughness effect on the Performance of 3-lobe symmetric hole entry hybrid journal bearings”, International Mechanical Engineering Congress (IMEC-2014), NIT Tiruchirappalli, India. Paper Abstract ID: IMEC 2014-G-015, June 13-15, 2014.
  15. Satish C. Sharma, Arvind K. Rajput,   Study of Geometrically Imperfect Multirecess Hybrid Journal Bearing System with different Pocket GeometriesSTLE 68th Annual Meeting & Exhibition  2013, Lake Buena Vista, Florida. May 18-22, 2014.
  16. S. S. Harak, Satish C. Sharma and S. P. Harsha, Structural dynamic analysis of freight railway wagon using finite element method, Presented at 3rd International Conference on Materials Processing and Characterisation (ICMPC 2014), Hyderabad, India (March 2014).
  17. Arvind K. Rajput, Satish C. Sharma, “Influence of geometrically imperfect misaligned journal on the performance of CFV compensated 4 pocket hybrid journal bearing”, International Conference on Advances in Tribology (ICAT -2014), NIT Calicut, India. pp.  Feb. 21-24, 2014.
  18. Prashant B. Kushare and Satish C.Sharma, “Influence of Wear on the Performance Analysis of Non-Circular Non-Recessed Hybrid Journal Bearing Configurations”, International Conference on Advances in Tribology (ICAT-2014), NIT Calicut, India. Paper No.183, Feb. 21-24, 2014.
  19. Saurabh Kumar Yadav and Satish C Sharma, “Performance analysis of a partial textured hydrodynamic thrust bearing operating with non-Newtonian lubricant” International Conference on Advances in Tribology (ICAT-2014), NIT Calicut, India, 21-24 Feb, 2014.
  20. Saurabh Kumar Yadav and Satish C. Sharma, “Combined influence of tilt on the performance of hybrid thrust bearing system operating with non-Newtonian Lubricant”, ASIATRIB-2014, Agra 17-20 Feb 2014.
  21. Satish C. Sharma, Arvind K. Rajput,   “A Study of Orifice compensated geometric imperfect four pocket hydrostatic Journal bearing Operating with Micropolar Lubricant”, ASIATRIB -2014,  Hotel Jaypee Palace, Agra, (India).  Paper Id- TSI914544, Feb. 17-20, 2014.
  22. Arvind K. Rajput,, Satish C. Sharma, “Effect of undulations of the journal on the performance of multi-recess conical hybrid journal bearing”, ASIATRIB -2014,  Hotel Jaypee Palace, Agra, (India).  Paper Id- TSI914545, Feb. 17-20, 2014.
  23. Prashant B.Kushare and Satish C.Sharma , “Performance of Two Lobe Hole Entry Worn Hybrid Journal Bearing System Operating with Non-Newtonian Lubricant”, ASIATRIB-2014, Hotel Jaypee Palace, Agra, (India).  Paper Id- TSI914531, Feb. 17-20, 2014. 
  24. Satish C. Sharma Arvind K. Rajput,  “Influence of Geometric Irregularities of Journal on the   Performance of Capillary Compensated Multirecess Hydrostatic Journal Bearing” STLE 68th Annual Meeting & Exhibition  2013, Detroit, Michigan (USA). Control ID: 1531772, May 07, 2013
  25. Arvind K. Rajput, Satish C. Sharma,  “Stability of a Constant Flow Valve Compensated Multirecess Conical Hybrid Journal Bearing Operating with Micropolar Lubricant”  ITS 2013, Lulea university of Technology,  Lulea, Sweden, 19-21 March 2013.
  26. Satish C. Sharma, Ram Nathi, “Combined Influence of Surface roughness and  Micropolar Lubricant on the Performance of Constant valve Compensated Hole-Entry Hybrid Journal Bearing”, International Conference on Industrial Tribology (ICIT-2012), Pune, India.TSI-812517.
  27. Ram Nathi, Satish C. Sharma, “Influence of Couple Stress Lubricant on the Performance of Symmetric and Asymmetric Hole-Entry Hybrid Journal Bearing”, International Conference on Industrial Tribology (ICIT-2012), Pune, India.TSI-812518.
  28. Vikas M. Phalle, Satish C. Sharma, “Influence Of Wear Depth Parameter on the Performance Of Four Pocket/Six Pocket Hybrid Conical Journal Bearing System”, International Conference on Industrial Tribology (ICIT-2012), Pune, India. TSI-812531.
  29. Arvind K. Rajput, Satish C. Sharma, “A Study of Orifice Compensated 4-Pocket Conical Hydrostatic Journal Bearing operating with Micropolar Lubricant”, International Conference on Industrial Tribology (ICIT-2012), Pune, India. TSI-812572.
  30. Prashant B. Kushare, Satish C. Sharma, “ Performance evalution of Two Lobe Multirecesss Worn Hybrid journal bearing operating under turbulent regime”, International Conference on Industrial Tribology (ICIT-2012), Pune, India.TSI-812598.
  31. Saurabh K. Yadav,Satish C. Sharma, “ Study On The Influence of Operating Parameters On The Elastohydrodynamically Lubricated Gear Contacts”, International Conference on Industrial Tribology (ICIT-2012), Pune, India.TSI-812601.
  32. Satish C. Sharma, Ram Nathi, “Influence of Couple Stress Lubricant on the Performance of Orifice Compensated Non-Recessed Hole-Entry Hybrid Journal Bearing”, STLE/ASME 2012 International Joint Tribology Conference, IJTC2012, Westin Denver Downtown, Denver, Colorado. (USA), October 7-10, 2012, Paper No. IJTC2011-61087, 2012.
  33. Satish C. Sharma, Nathi Ram,Influence of Micropolar Lubricants on the performance of an Orifice Compensated Rough Hole-Entry Hybrid Journal Bearing”, Proceedings of 67th STLE2012 Annual Meeting & Exhibition, St. Louis, Missouri (USA), May 6-10, Manuscript ID-1244039, 2012.
  34. Nathi Ram, Satish C. Sharma, “Performance of Constant Flow Valve Compensated Hole-Entry Hybrid Journal Bearing operating with Couple Stress Lubricant”, Proceedings of 67th STLE2012, Annual Meeting & Exhibition, St. Louis, Missouri (USA), May 6-10, Manuscript ID-1244032, 2012.
  35. Anand Y Joshi, Satish C Sharma, S.P.Harsha, “Analysis of Single walled Carbon Nanotubes with multiple defects”, Proceedings of the International conference on Fourth International conference on Structural Stability and Dynamics (ICSSD-2012), organized by Department of Structural Engineering, Malaviya National Institute of Technology (MNIT), Jaipur, January 4 – 6, 2012, 996.
  36. Vikas M. Phalle, Satish C. Sharma and S.C. Jain, “Influence of wear on the performance of a 2-lobe four-pocket hydrostatic journal bearing compensated with capillary restrictor,” Proc. of the 5th International Conference on Advances in Mechanical Engineering (ICAME-2011), S.V. National Institute of Technology, Surat, Gujarat, India, June 06-08 2011, pp.783-787,2011.
  37. Nathi Ram, Satish C. Sharma, “Performance of a Constant Flow Valve compensated Non-Recessed Hole-Entry Hybrid Journal Bearing operating with Micropolar Lubricant”, STLE/ASME 2011 International Joint Tribology Conference, IJTC2011, Marriott Los Angeles, California (USA), October 24-26, Paper No. IJTC2011-61087, 2011.
  38. Nathi Ram, Devendra Sankla, Arvind  K. Rajput and Satish C. Sharma, “Performance of  an Orifice Compensated Non-Recessed Hole-Entry Hybrid Journal Bearing Operating in Turbulent regime”, Proceedings of ASME 2011 International Design Engineering Technical Conferences & Computers and Information in Engineering Conference, IDETC/CIE-2011, Washington, DC (USA), August 28-31, 2011.
  39. Arvind  K. Rajput and Satish C. Sharma, “A Parametric study of ‘S’ Shape Coriolis Mass flow meter”, Proc. Of 1st International conference for Materials and Applications for Sensors  and Transducers (ICMAST-2011)  Kos Island, Greece during May 13-17, 2011.
  40. Arvind  K. Rajput and Satish C. Sharma, “An experimental study of ‘S’ Shape (copper) Coriolis Mass flow Sensor”, Proc. Of 5th International conference on Advances in mechanical engineering (ICAME-2011)  SVNIT,Surat , Gujrat(India), June 06-08,2011.
  41. Vikas M. Phalle, Satish C. Sharma and S.C. Jain, Influence of Wear on the Performance of a 2-Lobe Four-Pocket Hydrostatic Journal Bearing Compensated with Capillary Restrictor”, Proc. of the 5th International Conference on Advances in Mechanical Engineering (ICAME-2011), S.V. National Institute of Technology, Surat, Gujarat, India, June 06-08, 2011
  42. Nathi Ram, Devendra Sankla, Satish C. Sharma, “Performance of a Constant Flow Valve Compensated Non-Recessed Hole-Entry Hybrid Journal Bearing Operating in Turbulent Regime”, STLE Annual Meeting, Atlanta, Georgia (USA), on May 15-19, 2011.
  43. Satish C. Sharma and Nathi Ram,  “Performance of an Orifice Compensated Non-Recessed Hole-Entry Hybrid Journal Bearing Operating with Micropolar Lubricant”, STLE Annual Meeting, Atlanta, Georgia (USA), on May 15-19, 2011.
  44. Satish C. Sharma, Vikas M. Phalle, and S. C. Jain, “Influence of Wear and Method of Compensation on the Performance of 2-Lobe Multirecess Hybrid Journal Bearing System”,STLE-2011, Hilton Atlanta,255 Courtland St Ne,Atlanta, Ga. (USA), May 15-19, 2011.
  45. P.K. Kankar, Satish C. Sharma and S.P. Harsha, Fault Diagnosis of Rolling Element Bearings Using Artificial Neural Networks and Self Organizing Maps Using Complex Morlet Wavelet, Proceedings of the 7th International Conference on Industrial Tribology, December 2-4, 2010, Ispat Bhawan, Ranchi, India.
  46. Nathi Ram, Satish C. Sharmaand S. C. Jain, “A capillary compensated hole-entry hybrid misaligned journal bearing operating in turbulent regime”, 7th International Conference on Industrial Tribology ,ICIT-2010, Ispat Bhawan, Ranchi, India, Dec. 1-4, 2010.
  47. Nathi Ram, Satish C. Sharma and S. C. Jain, “Influence of journal misalignment and wear on the performance of constant flow valve compensated non-recessed hybrid journal bearing operating in turbulent regime”, Paper no: A065, 7th International Conference on Industrial Tribology ,ICIT-2010, Ispat Bhawan, Ranchi, India, Dec. 1-4, 2010.
  48. Vikas M. Phalle, Satish C. Sharma and S. C. Jain, “Performance characteristics of 3-lobe four-pocket hybrid journal bearing system compensated with orifice restrictor by considering the influence of wear”, Paper no: A064, 7th International Conference on Industrial Tribology, ICIT-2010, Ispat Bhawan, Ranchi, India, Dec. 1-4, 2010.
  49. Satish C. Sharma and E. Rajasekhar Nicodemus, “A comparative study of a multirecess hybrid worn journal bearing system operating in turbulence regime compensated with different flow control devices”, Proceedings of International joint tribology conference 2010, Paper no: 41027, San Francisco, Oct 18-20, 2010.
  50. Satish C. Sharma, Vikas M. Phalle and S. C. Jain, ‘Performance of Noncircular 2-Lobe Multirecess Constant Flow Valve Compensated Hybrid Journal Bearing by Considering Wear’, Proceedings of STLE Annual Meeting, Las Vegas, Nevada, on May 16-20, 2010.
  51. Sharma Satish C., Nathi Ram, Jain S.C., “Combined Influence of Journal Misalignment and Wear on the performance of Orifice Compensated Non-Recessed Hybrid Journal Bearing in Turbulent Regime”, Accepted for Presentation in STLE Annual Meeting, Las Vegas, Nevada, on May 16-20, 2010.
  52. P.K. Kankar, S. P. Harsha and Satish C. Sharma, ‘A Comparative study on Bearing Faults Classification by ANN and SOM using Complex Morlet Wavelet’, IV European Conference on Computational Mechanics, Paris, France, May 16-21, 2010.
  53. P.K. Kankar, S. P. Harsha and Satish C. Sharma, ‘Vibration Monitoring of Localized defects in Rolling Element Bearings’, IV European Conference on Computational Mechanics, Paris, France, May 16-21, 2010.
  54. P. K. Kankar, Satish C. Sharma and S. P. Harsha, ‘Vibration based Fault Diagnosis of Rolling Element Bearings using Response Surface Method, 54th Congress of ISTAM (An International Meet), Netaji Subhas Institute of Technology, New Delhi, December 18-21, 2009.
  55. Anand Y. Joshi, Satish C. Sharma and S. P. Harsha, ‘Mass Sensitivity of Single Walled Carbon Nano-Tube Based Nano Mechanical Resonators’, 54th Congress of ISTAM (An International Meet), Netaji Subhas Institute of Technology, New Delhi, December 18-21, 2009.
  56. Pravin P Patil, Satish C. Sharma, Prabhakar Singh, S.C.Jain, “Finite Element Modeling of Vibration Based Mass Flow Sensors”, Proceedings of 54th Congress of ISTAM (An International Meet), Netaji Subhas Institute of Technology, New Delhi, December 18-21, 2009.
  57. Vikas M. Phalle, Satish C. Sharma, and S. C. Jain, ‘A Study of Noncircular 2-Lobe Multirecess Hydrostatic Worn Journal Bearing with Orifice Compensation’, Proceedings of 54th Congress of ISTAM (An International Meet), Netaji Subhas Institute of Technology, New Delhi, December 18-21, 2009.
  58. E. Vijaya Kumar, Vikas M. Phalle, Satish C. Sharma and S. C. Jain,  ‘Performance of 4-pocket capillary compensated worn hybrid journal bearing’ 3rd international Congress on Computational Mechanics and Simulation (ICCMS09) IIT-Bombay, Mumbai-400 076, INDIA , December 1-5,  2009.
  59. Vijay Kumar E, Vikas M. Phalle, Satish C. Sharma, S.C. Jain, ‘Analysis of a worn Multirecess Hydroststatic Journal Bearing System’, Proceedings of ASME 2009 International Design Engineering Technical Conferences & Computers and information in Engineering Conference, Proceedings of IDETC/CIE-2009, August 30- Sept. 2, 2009, San Diego, Californiia USA, Paper No. DETC 2009-86787.
  60. Rakesh Kamra, S. H. Upadhyay, P.K. Kankar, S. C. Jain, Satish C. Sharma and S. P. Harsha, ‘ANN Based Fault Diagnosis of Rolling Element Bearings’, Proceedings of  IUTAM Symposium on Emerging Trends in Rotor Dynamics’, Paper-31, March 23-26, 2009, Delhi, India.
  61. P. K. Kankar, Kalyan Manohar B., Aashish B., Satish C. Sharma and S. P. Harsha, ‘Vibration Based Fault Diagnosis of Rolling Element Bearings using Artificial Neural Networks and Support Vector Machines’, Proceedings of Conference on Dynamics, Vibration and Control, August 10-15, 2009, Chengdu, China.
  62. Aashish Bhatnagar, P. K. Kankar, Satish C. Sharma and S. P. Harsha, ‘ANN Based fault classification of High speed ball bearings’, Proceedings of the ASME 2009 International Design Engineering Technical Conferences & Computers and Information in Engineering Conference, August 30-September 2, 2009, San Diego, California, USA.
  63. Kalyan M. Bhavaraju, P. K. Kankar, Satish C. Sharma and S. P. Harsha, ‘Fault Diagnosis of Ball Bearings using Soft Computing’, Proceedings of the ASME 2009 International Design Engineering Technical Conferences & Computers and Information in Engineering Conference, August 30-September 2, 2009, San Diego, California, USA.
  64. P. K. Kankar, Satish C. Sharma and S. P. Harsha, ‘Vibration Signature Analysis of a Rotor Bearing System using Response Surface Method’, Proceedings of the ASME 2009 International Design Engineering Technical Conferences & Computers and Information in Engineering Conference, August 30-September 2, 2009, San Diego, California, USA.
  65. Vijay Kumar E, Vikas M. Phalle, Satish C. Sharma, S.C. Jain, ‘Analysis of a worn Multirecess Hydroststatic Journal Bearing System’, Proceedings of ASME 2009 International Design Engineering Technical Conferences & Computers and information in Engineering Conference, IDETC/CIE-2009, August 30- Sept. 2, 2009, San Diego, Californiia USA, Paper No. DETC 2009-86787.
  66. J. S. Basavaraja, S. C. Jain, Satish C. Sharma, ‘Influence of ER Fluid Lubrication on the Performance of a Rough Hole-Entry Hybrid Journal Bearing System’, Proceedings of  IUTAM Symposium on Emerging Trends in Rotor Dynamics, IIT Delhi, India, March 23-26, 2009.
  67. R.K. Awasthi, Satish C. Sharma, and S.C. Jain,Static Performance of Capillary Compensated Multiple Hole-Entry Hybrid Worn Journal Bearing in Turbulence Regime’ Proceedings of International Conference on Industrial Tribology (ICIT 2008) New Delhi, Nov. 6-8, 2008.
  68. J.S. Basavaraja, Satish C. Sharma, and S.C. Jain, ‘The Study of ER Fluid Lubricated Misaligned Hole--Entry Hybrid Journal Bearing’, 2nd International Conference on Advanced Tribology 2008, National Singapore University, Singapore, Dec. 3-5, 2008.
  69. S. P. Harsha and Satish C. Sharma, “Nonlinear Dynamics of High Speed Unbalanced Rotor Supported on Rolling Element Bearings due to Waviness”, Proceedings of International Conference on Industrial Tribology (ICIT 2008), New Delhi, Nov. 6-8, 2008.
  70. J.S. Basavaraja, S.C. Jain and Satish C. Sharma, ‘Constant Flow Valve Compensated Hole-Entry Hybrid Journal Bearing Lubricated with ER Fluid’, Proceedings of International Conference on Industrial Tribology (ICIT 2008), New Delhi, Nov. 6-8, 2008.
  71. S.C. Jain, J.S. Basavaraja and Satish C. Sharma, ‘Performance of a Misaligned Two Lobe Hole-Entry Hybrid Journal Bearing’, Proceedings of International Conference on Industrial Tribology (ICIT 2008), New Delhi, Nov. 6-8, 2008.
  72. Satish C. Sharma, J.S. Basavaraja and S.C. Jain, 'A Comparative Study on the Performance of Circular, Two-Lobe and Three-Lobe Hole-Entry Hybrid Journal Bearing', Proceedings of International Conference on Industrial Tribology (ICIT 2008), New Delhi, Nov. 6-8, 2008.
  73. J.S. Basavaraja, Satish C. Sharma, and S.C. Jain, ‘The Effect of Geometry on the Performance of the Hole-Entry Hybrid Journal Bearing Lubricated with ER Fluid’, Proc of 11th Conference on Electrorheological Fluids and Magnetorheological Suspensions, Technical University Dresden, Germany, Aug. 25-29, 2008.
  74. J.S. Basavaraja, S.C. Jain and Satish C. Sharma, ‘A Study of Smart Fluid Lubricated Non-Recessed Hybrid Journal Bearing’, Presented at Fifth ISSS International  Conference on Smart Materials, Structures and Systems’, IISc Bangalore, July 24-26, 2008, Paper No. 81.
  75. J.S. Basavaraja, S.C. Jain and Satish C. Sharma, ‘The Effect of Journal Misalignment on the Performance of Non-Recessed Hybrid Journal Bearing Lubricated With ER Fluid’, Proceedings of Twelths Nonlinear Vibrations, Dynamics, and Multibody Systems, June 1-5, 2008, Virginia Tech, Blacksburg, VA(USA).
  76. J.S. Basavaraja, Satish C. Sharma, and S.C. Jain, ' A Simulation Study of Rough Hole-Entry Hybrid Journal Bearing Lubricated with ER Fluid,' ICAME Conference , IISc Bangalore, July 2-4, 2008.
  77. K. Jagadeesha, T. Nagaraju, Satish C. Sharma, and S.C. Jain, ‘Transient Non – Newtonian Thermohydrodynamic Analysis of a Dynamically Loaded Journal Bearing with 3D Surface Roughness Effects’, Proc. of 63rd STLE Annual Meeting, Cleaveland Ohio, USA, May 18 – 22, 2008.
  78. Satish C. Sharma, S.C. Jain, J.S. Basavaraja, and Neeraj Sharma, ‘Combined Influence of Pocket Size and Journal Misalignment on the Performance of Hole – Entry Hybrid Journal Bearing System’, Proc. of 63rd STLE Annual Meeting, Cleaveland Ohio, USA, May 18 – 22, 2008, Abstract ID No. 393906.
  79. S.C. Jain, Satish C. Sharma, J.S. Basavaraja and Pranshat Kushare, ‘A Study of Two Lobe Four Recessed Compensated Hybrid Journal Bearing System’, Proc. of 63rd STLE Annual Meeting, Cleaveland Ohio, USA, May 18 – 22, 2008, Abstract ID No. 393860.
  80. T. Nagaraju, Sharana Basavaraja J., S.C. Jain, and Satish C. Sharma, 'A Study of Orifice Compensated Multilobe Hole – Entry Hybrid Journal Bearing', Proc. of 21st Biennial Conference on Mechanical Vibration and Noise (IDETC 2007), Las Vegas, Nevada, USA, September 04 -–07, 2007, Paper No. 35923.
  81. Prashant Kushare, Satish C. Sharma, S.C. Jain and Sharana Basavaraja J., ‘Performance of Two Lobe Multirecess Hybrid Journal Bearing Compensated With Capilary Restrictor', Proc. of STLE/ASME Internaitonal Joint Tribology Conference (IJTC2007), San Diego, California, USA, October 22 – 24, 2007, Paper No. 44433.
  82. Jagadeesha K.M., Nagaraju T., Satish C. Sharma, and S.C. Jain, 'Transient Non – Newtonian Analysis of a Rough Journal Bearing', International Conference on Industrial Tribology, IISc Bangalore, Nov. 30 – Dec. 02, pp. 672 - 680, 2006.
  83. Paras Kumar, Satish C. Sharma, and S.C. Jain, 'A Study on the Performance of a TCF Multirecess Hydrostatic/Hybrid Journal Bearing', International Conference on Industrial Tribology, IISc Bangalore, Nov. 30 – Dec. 02, 2006, pp. 688 - 703, 2006.
  84. Awasthi R.K., Satish C. Sharma, and S.C. Jain, 'Effect of Turbulence on the performance of non – Recessed Hole Entry Hybrid Journal Bearing System', International Conference on Industrial Tribology, Nov. 30 – Dec. 02, 2006, IISc Bangalore, pp. 146 – 153, 2006.
  85. Sharana Basavaraja J., S.C. Jain,  and Satish C. Sharma, 'Performance of a Multilobe Hole –Entry Hybrid Journal Bearing', International Conference on Industrial Tribology, Nov. 30 – Dec. 02, 2006, IISc Bangalore, pp. 135 – 146, 2006.
  86. T. Nagaraju, Satish C. Sharma, and S.C. Jain, 'Influence of Surface Roughness on Non – Newtonian Thermohydrostatic Performance of Hole – Entry Hybrid Journal Bearing', Proceedings of IJTC, Oct. 23 – 25, San Antonio, Texas, 2006, (U.S.A.) Paper No. : IJTC: 12101.
  87. R.K. Awasthi, Satish C. Sharma, and S.C. Jain, 'Effect of Wear on the Performance of Non – Recessed Orifice Compensated Hybrid Journal Bearing', Proceedings of  Published in 61st STLE Annual Meeting , Calgary, Canada, May 7-11, 2006, Paper No. : AM (NP)-06-01.
  88. Vijay Kumar, Satish C. Sharma and S.C. Jain, “Journal Motion Simulation of Hybrid Journal Bearing Considering Viscosity Variation due to Temperature Change”,  Proceedings of IMECE 2005, Proceedings of 2005 ASME International Mechanical Engineering Congress and Exposition, Nov. 5-11, 2005 Orlando, Florida, U.S.A.
  89. R.K. Awasthi, Satish C. Sharma and S.C. Jain, 'Influence of Grid on Average Flow Factors for Isotropic Surface Roughness in Hydrodynamic Lubrication', Proceedings of International Conference on Industrial Tribology, ICIT – 04, Mumbai, Dec. 15 – 18, 2004, pp. 337 – 343.
  90. R.K. Awasthi, S.C. Jain and Satish C. Sharma, 'Code Development for the Analysis a Finite Journal Bearing System using Matlab', Proceedings of International Conference on Industrial Tribology, ICIT – 04, Mumbai, Dec. 15 – 18, 2004, pp. 501 – 507.
  91. M. Bhasker Rao, Satish C. Sharma, S.C. Jain and R.K. Awasthi, 'Influence of Geometric Shape of Recess on the Performance of a Six – Pocket Hybrid Journal Bearing System', Proceedings of International Conference on Industrial Tribology, ICIT – 04, Mumbai, Dec. 15 – 18, 2004, pp. 328 – 336.
  92. Vinod Patil, S.C. Jain, Satish C. Sharma, and Rakesh Kumar Gautam, 'Simulated Study of Sliding Wear', Proceedings of International Conference on Industrial Tribology, ICIT – 04, Mumbai, Dec. 15 – 18, 2004, pp. 442 – 447.
  93. Satish C. Sharma, Narendra Singh, S.C. Jain and S. Sanjeeva Reddy, ‘Performance of Multirecess Hydrostatic/Hybrid Journal Bearing of Various Recess Shapes Using Membrane Flow Valve Restrictor', Proceeding of Int. Conference of Fluid Mechanics, I.I.T. Roorkee, December 12-14, 2004, Vol. II, pp 711-723.
  94. Satish C. Sharma, T. Nagaraju and S.C. Jain, 'Performance of Orifice Compensated Hole – Entry Hybrid Journal Bearing System, Considering Surface Roughness and Thermal Effects', Proceedings of 2003 STLE / ASME, Joint International Tribology Conference, Ponte Vedra Beach, Florida U.S.A., Oct. 26-29, 2003, Paper No. Trib. – 11, pp. 1-21.
  95. T. Nagaraju, Satish C. Sharma, and S.C. Jain, 'Dynamic Performance Characteristics of Misaligned Hybrid Journal Bearing System Including Surface Roughness Effects', Proceedings of Int. Conference of Fluid Mechanics, I.I.T. Roorkee, December 12-14, 2002, Vol. II, pp. 705-710.
  96. Satish C. Sharma, T. Nagaraju and S.C. Jain, ‘Combined Influences of Journal Misalignment and Surface Roughness on the Performance of Orifice Compensated Non-Recessed Hybrid Journal Bearing’, proceedings of 57th Annual Meeting of STLE, Houston TX, May 19-2002, Technical Preprints, 02-NP-24, pp 609-620
  97. Vijay Kumar, Satish C. Sharma and S.C. Jain, ‘Performance of Orifice Compensated Hole-Entry Hybrid Journal Bearing Including Thermal Effects’, Proceedings of ICIT,2001, pp. 4-119 to 4-126, Jamshedpur (INDIA) 8th - 11th April 2002.
  98. Nagaraju T, Satish C. Sharma and Jain S. C., ‘Performance of Constant Flow Valve Compensated Hole-Entry Hybrid Journal Bearing Including Surface Roughness Effects’, Proceedings of ICIT,2001, pp. 4-41 to 4-49, Jamshedpur (INDIA) April  8-11, 2002.
  99. Narendra Singh, Satish C. Sharma and S. C. Jain, ‘The Influence of Geometric Shapes of Recess on the Performance of Orifice Compensated Multirecess Hybrid Journal Bearing’, Proceedings of ICIT,2001, pp. 4-31 to 4-40, Jamshedpur (INDIA), April  8-11, 2002.
  100. Satish C. Sharma, S. C. Jain and Rajneesh Kumar, ‘Effect of Size of a Hole on the Performance of a Capillary Compensated Hole-Entry Hybrid Journal Bearing’, Proceedings of ICIT,2001, pp. 4-22 to 4-30, Jamshedpur (INDIA), April  8-11, 2002.
  101. T. Nagaraju, Satish C. Sharma and S. C. Jain, ‘Static Performance of Misaligned Hole-Entry Hybrid Journal Bearing Including Surface Roughness Effects ‘, Proceedings of 4th International conference on Mechanical Engineering, December 26-28, 2001, Dhaka, Bangladesh, Section V, pp. 147-153. 2001.
  102. Satish C. Sharma, S.C. Jain and N. Madhu Mohan Reddy, ‘A Study of Non – Recessed Hybrid Flexible Journal Bearing with Different Restrictors’, ASME/STLE Tribology Conference, Seattle, WA, October 1 – 4, 2000 and Proceedings of a ASME/2000-Trib.8 (TC2000/STLE-10).
  103. Satish C. Sharma, S.C. Jain and B.V.N. Surendra Kumar, ‘Effect of Load Direction on the Hydrostatic/Hybrid Performance of a Multirecess Orifice Compensated Flexible Journal Bearing’, Proceedings of International Conference of Industrial Tribology-1999, Hyderabad, Dec. 1-4, pp.101-108, 1999.
  104. Vijay Kumar, Satish C. Sharma, S.C. Jain, ‘Transient Response of Capillary Compensated Hybrid Journal Bearing System During Starting and Stoping Operation’,  Proceedings of International Conference of Industrial Tribology – 1999,  Hyderabad, Dec. 1-4, 1999, pp.75-82, 1999.
  105. Satish C. Sharma, R. Sinhasan, S. C. Jain, N. Singh and S.K. Singh, ‘Performance of Hydrostatic/Hybrid Journal Bearing with Unconventional Recess Geometries’, Proc. of 52nd Annual Meeting of STLE, KANSAS CITY MISSOURI (U.S.A.), May 18-22, 1997.
  106. R. Sinhasan, S.C. Jain, P.L. Sah and Satish C. Sharma, ‘Dynamic Performance Characteristics of Hydrostatic/Hybrid Journal Bearing with Non-Newtonian Lubricants’, Proceedings of International Conference on Industrial Tribology, (ICIT-97), Calcutta (INDIA), Dec. 2-5, pp. 167-171, 1997.
  107. S.C. Jain, Satish C. Sharma and A. Jagtap, ‘Performance of Multirecess Hybrid Journal Bearing Operating in Turbulent Regime’, Proceedings of International Conference on Industrial Tribology (ICIT-97), Calcutta (INDIA), Dec. 2-5, pp. 172-177, 1997.
  108. Nagvendra kumar kanoje, Sharma, Satish C., and S. P. Harsha , Mass Reduction of Railway Wheel Using Response Surface Method Considering Natural Frequency and Wheel Dimension, Proceeding of 4th International Conference on Structural Stability.

 

Papers Published In National Conferences

  1. Vivek Kumar and Satish C. Sharma, “Performance of Circular Recessed Hydrostatic Tilted Thrust pad Bearing Operating with Couple Stress Lubricant”, National Tribology conference (NTC-2016), IIT BHU, Varanasi (India), Paper No. NTC-2016-557, Dec. 08-10, 2016.
  2. Chandra B. Khatri and Satish C. Sharma, “A study of a textured slot-entry hybrid journal bearing system operating with power law lubricant”, National Tribology conference (NTC-2016), IIT BHU, Varanasi (India), Paper No. NTC-2016-514, Dec. 08-10, 2016.
  3. Satish C. Sharma and Chandra B. Khatri, “Performance analysis of a 3-lobe textured slot-entry hybrid journal bearing system ”, National Tribology conference (NTC-2016), IIT BHU, Varanasi (India), Paper No. NTC-2016-562, Dec. 08-10, 2016.
  4. Dharmendra Jain and Satish C. Sharma, “Static and Dynamic Characteristics of a Geometrically Imperfect CFV Compensated Two-Lobe Hybrid Journal Bearing Lubricated With Power Law Lubricant”, National Tribology conference (NTC-2016), IIT BHU, Varanasi (India), Paper No. NTC-2016-556, Dec. 08-10, 2016.
  5. Suresh Jadhav and Satish C. Sharma, “Film thickness in Elasto-hydrodynamic lubricated point contacts”, National Tribology conference (NTC-2016), IIT BHU, Varanasi (India), Paper No. NTC-2016-558, Dec. 08-10, 2016
  6. Saurabh K. Yadav, Nathi Ram and Satish C. Sharma, “Performance of hybrid tilted and textured thrust pad bearing”, National Tribology conference (NTC-2016), IIT BHU, Varanasi (India), Paper No. NTC-2016-590, Dec. 08-10, 2016
  7. Nathi Ram, Saurabh K. Yadav and Satish C. Sharma, “Performance of asymmetric hole-entry hybrid journal bearing using CFV restrictor under micropolar lubrication”, National Tribology conference (NTC-2016), IIT BHU, Varanasi (India), Paper No. NTC-2016-502, Dec. 08-10, 2016
  8. Satish C. Sharma, “Hydrostatic/Hybrid Bearings - Some Recent Advances”, Proceedings Tribology Frontiers Workshop 03-04th Aug, Indian Institute of Engineering Science and technology Shibpur, Howrah, 2016.
  9. Prashant B.Kushare and Satish C. Sharma, “A study of multilobe slot entry hybrid journal bearing”, National Tribology conference (NTC-2014), PES University, Bengaluru (India), Paper No. NTC-2014-516, Dec. 15-18, 2014.
  10. Chandra B. Khatri and Satish C. Sharma, “Performance analysis of a capillary compensated partial non-recess hole entry hybrid journal bearing system”, National Tribology conference (NTC-2014), PES University, Bengaluru (India), Paper No. NTC-2014-505, Dec. 15-18, 2014.
  11. Dharmendra Jain and Satish C. Sharma, “Performance analysis of power law lubricated geometrically imperfect four lobe multi-recessed hybrid journal bearings”, National Tribology conference (NTC-2014), PES University, Bengaluru (India), Paper No. NTC-2014-506, Dec. 15-18, 2014.
  12. Saurabh K. Yadav and Satish C. Sharma, “Study of circular hydrostatic tilted thrust pad bearing by considering temperature variation of oil film”, National Tribology conference (NTC-2014), PES University, Bengaluru (India), Paper No. NTC-2014-515, Dec. 15-18, 2014.
  13. Nathi Ram, Saurabh K. Yadav and Satish C. Sharma, “Static performance of Hole-Entry hybrid Journal Bearing operating under turbulence Regime”, National Tribology conference (NTC-2014), PES University, Bengaluru (India), Paper No. NTC-2014-507, Dec. 15-18, 2014.
  14. Nathi Ram, Satish C. Sharma, “Comparative Study of the Performance of Constant Flow Valve and Capillary Compensated Non-Recessed Hole-Entry Hybrid Journal Bearing operating with Micropolar Lubricants”, Proceedings of 1st National Tribology Conference (NTC 2011), IIT Roorkee, Roorkee (India), December 08-10, Paper No. NTC-201124, 2011.
  15. Satish C. Sharma, Somesh Sharma, Sumit Wadhwa and Suren Kumar, ‘Design an Electrically Assisted Multi-Terrain Human Powered Vehicle’, Proc. Of 3rd UttaraKhand state Science and Technology Congress’. IIT Roorkee, Nov. 10-11, 2008, pp167.
  16. K.M. Jagdeesha, T. Nagaraju, V.K. Jadon, Satish C. Sharma and S.C. Jain, ' Stability of Hole – Entry Hybrid Journal Bearing Lubricated with Non – Newtonian Lubricant From Linear and Non – Linear Transient Analysis', Proceedings of First International and 22nd AIMTDR Conference, Dec. 21 – 23, 2006, pp. 199-204, Deptt. of Mech. & Ind. Engg., I.I.T. Roorkee, Roorkee 247 667.
  17. R.K. Awasthi, Satish C. Sharma, and S.C. Jain, 'A Parametric Study on the Performance of Hole – Entry Hybrid Worn Journal Bearing System', Proceedings of National Conference on Advances in Mechanical Engineering (AIME – 2006), Faculty of Engg. & Technology, Jamia Millia Islamia, New Delhi, Jan. 20-21, 2006, pp. 9-20.
  18. R.K. Awasthi, Satish C. Sharma, and S.C. Jain, 'Effect of Grid Size on Hydrodynamic Journal Bearing Performance', Proceedings of the Conference on Computer Aided Design and Manufacturing: A Global Perspective MED, TIET, Patiala, April 8-9, 2005.
  19. Narendra Singh, Satish C. Sharma, and S.C. Jain, 'Performance of Constant Flow Valve Compensated Multirecess Hydrostatic / Hybrid Journal Bearing of Different Recess Geometries', Proceedings of National Conference on Recent Development in Mechanical Engineering, Mech. Engg. Deptt., TIET, Patiala, Oct. 31st - 1st Nov.,  2003, pp. 264 – 270.
  20. Vijay Kumar, Satish C. Sharma, S.C. Jain and Y.J. Rajput, ‘Thermohydrostatic Analysis of Capillary Compensated Hole – Entry Hybrid Journal Bearing’, Proceedings of Sixteenth National convention of Mechanical Engineers, Department of Mechanical and Industrial Engineering, University of Roorkee, Roorkee, pp. 109-116, September 29 – 30, 2000.
  21. T.Nagaraju, Satish C. Sharma, S.C. Jain, ‘Performance of Constant Flow Valve Compensated Hole-Entry Hybrid Journal Bearing Considering Journal Misalignment’, Sixteenth National convention of Mechanical Engineers, Department of Mechanical and Industrial Engineering, University of Roorkee, Roorkee, pp. 133-139, September 29 – 30, 2000.
  22. S.C.Jain, R. Sinhasan, Satish C. Sharma and V.H. Saran, ‘Comparative Assessment of 3-Pocket and 4-Pocket Journal Bearing Systems’, Proceedings of 9th ISME Conference on Mechanical Engineering, Deptt. of Mech. and Ind. Engg., University  of Roorkee, Roorkee – 247 667, Nov. 10-11, 1994,  pp. 579-583.

R. Sinhasan, S.C. Jain  and Satish C. Sharma, ‘Elastic Considerations in Performance Characteristics of Hydrostatic Bearings’, 12th AIMTDR Conference, IIT Delhi on Dec. 12, 1986, pp. 1030(1)-1030(4).